Search found 129 matches

by Enlive
Sat May 14, 2016 6:29 am
Forum: HT Venue Series
Topic: HT Club 50 or HT Stage 100 for rehearsal space?
Replies: 9
Views: 11096

Re: HT Club 50 or HT Stage 100 for rehearsal space?

The 50 is more than enough headroom and power for either. Also its much easier to dial the tone in with the 50 being the clean has just one tone knob and it doesn't have presence and resonance meaning you can't push the dreaded high end fizz or the unneeded sub bass rumble too much even if you wante...
by Enlive
Fri May 13, 2016 2:09 pm
Forum: Blackstar Amps
Topic: Controlling noise gate on ID:TVP15
Replies: 3
Views: 5664

Re: Controlling noise gate on ID:TVP15

Ya only through the software. Honestly though just as something to try out, and this is from someone who loves the ID apps and has two for over two years now, the Super Crunch channel with gain no higher than 3o'clock is the best channel for metal and the crunch channel even with gain maxed out is t...
by Enlive
Thu May 12, 2016 4:57 pm
Forum: ID:Series
Topic: ID:15TVP - 2 Questions
Replies: 8
Views: 9580

Re: ID:15TVP - 2 Questions

Make sure your amp is update. PLug in via USB and insider will automatically start it. Then WHILE HOLDING DOWN TAP the Bass = Resonance, Treble = Presence and ISF = Mid. When altering these only the Mid will flash green to let you know where youve stored it. Presence and Resonance can't be stored so...
by Enlive
Thu May 12, 2016 4:48 pm
Forum: HT Venue Series
Topic: Emulated line out
Replies: 2
Views: 5713

Re: Emulated line out

Just plug into the mic in. It would be best to purchase a used interface for cheap but mic in will do the job.
by Enlive
Thu May 12, 2016 4:44 pm
Forum: ID:Series
Topic: Strange things happinng with FS 10
Replies: 9
Views: 11171

Re: Strange things happinng with FS 10

Try plugging the amp in via USB and make sure it doesn't need an update. Mine did the same but after i updated it it was smooth like butter. Good luck!
by Enlive
Wed May 11, 2016 7:28 am
Forum: Blackstar Amps
Topic: Blackstar HTV 2 X12 Extension Cabinet
Replies: 2
Views: 3261

Re: Blackstar HTV 2 X12 Extension Cabinet

You would need to buy 16 ohm speakers to swap. I recommend v30s.
by Enlive
Wed May 11, 2016 7:26 am
Forum: Blackstar Amps
Topic: ID 60 1x12 speaker swap?
Replies: 52
Views: 49916

Re: ID 60 1x12 speaker swap?

Seeing as the Blackstar ID 4x12 cab comes w Celestion Seventy80 speakers, that would be my first choice. Although the ID TVP amps have the Series One 6 channels and the Series One cabs come w/ Celestion V30s. 8 ohms will be best bet to lose minimal power but not a really noticeable dip so no worries...
by Enlive
Tue Apr 26, 2016 5:07 am
Forum: Blackstar Amps
Topic: IDCore10 USB recording = a total mess!!
Replies: 4
Views: 5097

Re: IDCore10 USB recording = a total mess!!

Just used the emulated out to an interface or your computer's mic input.
by Enlive
Mon Apr 25, 2016 5:21 pm
Forum: Show us your Blackstar set-up
Topic: Post your Blackstar amp!
Replies: 203
Views: 286954

Re: Post your Blackstar amp!

Love my ID:60TVP!!! 2x12 loaded with V30s and EL34 tone. Cuts the mix like butter
by Enlive
Mon Apr 25, 2016 5:12 pm
Forum: Show us your Blackstar set-up
Topic: Post your Blackstar amp!
Replies: 203
Views: 286954

Re: Post your Blackstar amp!

Does the Id60 tvpH run safely with an 8 ohm cab such as the mesa cab you are using? Yes it's always safe to go higher in ohms but never less. Don't put a 4ohm cab into an 8ohm jack in the head but the opposite, 8ohm cab to a 4ohm jack is A OKAY. You just lose a small amount of volume but so little ...